Mitre Fast Bonding Kit everbuild

Mitre Fast Bonding Kit

Two part instant adhesive system

Product Description

EVERBUILD MITRE FAST is a two pack system comprising an extremely high viscosity ethyl cyanoacrylate adhesive (50g) a 200ml aerosol activator. Used primarily for instant bonding (10 seconds) of wooden mitre joints, with numerous other uses.

Activator aerosol and adhesive are also sold as separate stock items.

 

 

Benefits

§  Flash setting formulation - bonds most surfaces within 10 seconds, cutting down dramatically mitre assembly bonding times when compared to conventional wood adhesives.

§  High viscosity adhesive – low soak in to give greater bond strength than conventional cyanoacrylates on porous surfaces (eg wood)

§  Gap filling – high viscosity adhesive will fill small gaps in mitres etc (up to 0.2mm)

§  Economical in use.

Code Product Boxed In
080027 Mitre Fast Bonding Kit 1

Areas For Use

§  Multitude of industrial applications: Bonds MDF, wood, chipboard, rubber, plastics, Perspex, uPVC ceramics, aluminium and metals.

§  Ideal for all cornice and profile mitres, trims, picture frames, MDF, skirting and architrave joints, worktop end strips, PVCu trims and much more. It is particularly useful for production lines such as electronics assembly and uPVC window trim bonding.

 

 

Limitations

§  Ensure surfaces are degreased prior to bonding.

§  Do not use on glass

§  Do not use in applications involving constant water immersion.

§  Do not use on bitumen or tar leaching products.

§  Do not use on load bearing applications – Use EVERBUILD ALL PURPOSE WOOD ADHESIVE.

§  On wooden/porous surfaces, do not use any other cyanoacrylate except MITRE FAST ADHESIVE. These products are thinner and the soak in will give poor bond strength.

 

               

 

 

 

 

Surface Preparation

The surfaces to be glued should be clean, dry and free from dust, grease and other contaminants. Materials should be stored in a warm environment prior to bonding to avoid chilling of the glue line, which leads to extended setting times. Where possible, ensure working environment has a relative humidity of 50% +.

 

Application

·      Spray one surface with activator.

·      Apply adhesive sparingly to other surface.

·      Bring together, position and hold for about 10 seconds.

 

Specific Data – Mitre Fast Adhesive

Base

Monomeric Ethyl cyanoacrylate

Solids

100% active

Viscosity

1,100mPas @ 20oC.

Therm. Cond.

0.2w/k.m              

Specific Gravity

1.07

Flash Point

> 83oC

Gap Filling Cap.

Up to 0.2mm

Refractive Index

1.45 (Cured adhesive)

Dielectric STR

11-13kV/mm

Dielectric Const.

5.2  @ 1MHZ         (cured adhesive)

Softening Point

165oC

Working Temps

-20 to +80oc

 

Specific Data – Mitre Fast Activator

Chemical Base

Hydrocarbon solvent

Appearance

Colourless

Viscosity

1mps @ 20oC.

Flash Point

0oC

Density

0.79g/cm3

Propellant

CO2

 

Health & Safety

Consult MSDS for full list of hazards.

 

Storage

Store in original unopened containers between 4 and 25oC. Reseal immediately once used.

Protect activator from sources of ignition.

 

Shelf Life

 Twelve months from date of manufacture in original unopened containers, depending on temperature of storage. As low temperature as possible will give maximum shelf life.

File Download
Mitre Fast - Adhesive and Activator New.doc
Mitre Fast - Adhesive iss 9.pdf